Arduino xbee sensor jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    16,706 arduino xbee sensor jobs found, pricing in AUD

    ...estimated the demand for high-speed internet in rural and regional Australia to be three times greater than originally anticipated only six years earlier. Advances in wireless sensor networks (WSNs) coupled with in-situ, low-cost sensors of soil moisture, plant biomass and local climate conditions means our fields and even our livestock are set to become

    $24 / hr (Avg Bid)
    $24 / hr Avg Bid
    9 bids

    ..."1","0","0","0","0","1","0"]} there are 10 values with 0 and 1 which is nothing but 10 relay ,receiving point in Arduino is already working as you know. You have to check this array if array has chnaged then u have to paas it to Arduino ,it means there is a change. This webservice should continuously hit and ge...

    $43 (Avg Bid)
    $43 Avg Bid
    7 bids

    ..."1","0","0","0","0","1","0"]} there are 10 values with 0 and 1 which is nothing but 10 relay ,receiving point in Arduino is already working as you know. You have to check this array if array has chnaged then u have to paas it to Arduino ,it means there is a change. This webservice should continuously hit and ge...

    $23 (Avg Bid)
    $23 Avg Bid
    2 bids

    Code for Arduino 2560 that will work as an TIME and ATTENDANCE LOGGER/ DATALOGGER. the code should support mag card swipe option and mag card swipe+pinpad/keypad option,,, More infoo in messages Thanks

    $284 (Avg Bid)
    $284 Avg Bid
    16 bids

    I need a Arduino sketch written for current home automation project. I am developing a voice controlled and push button controlled roll up shade using 1 DC MOTOR, 1 ARDUINO UNO R3 BOARD, 1 MDV 2x2A DC Motor Controller (L298N), 3 PUSH BUTTONS, 1 EASY VR SHIELD 3. I want to be able to setup EasyVR Shield to accept 'trigger' word as Blind and Group 2

    $217 (Avg Bid)
    $217 Avg Bid
    7 bids

    This project is for arduino code to communicate with an ELM327 with fords ms-can to write a value to a specific address in a specific module. For example to write to 720-01-03 FC27

    $201 (Avg Bid)
    $201 Avg Bid
    10 bids

    Write code to communicate IC2 connection between Raspberry 3b+ and Arduino Mega slave ( connected via logic level converter ). Arduino will perform quad (x4) BTS7960 43A H-Bridge motor control. Keyboard motor control script need to test. $50 budget

    $172 (Avg Bid)
    $172 Avg Bid
    6 bids

    we are usng arduino mega, Raspberry pi and some simple motor drivers. we just need to give you the schematic so that we can do the board.

    $219 (Avg Bid)
    $219 Avg Bid
    13 bids

    Hello. we need a kicad guy to help us move some stuff around our PCB. we have some initial tasks. we have already integrated all the components, we just n...guy to help us move some stuff around our PCB. we have some initial tasks. we have already integrated all the components, we just need to route and connect the PI to the Arduino via the pins.

    $209 (Avg Bid)
    $209 Avg Bid
    2 bids

    This project is to 1- Send proper commands from Xbee to samsung smartthings motion sensor and 2) read motion and temperature data. Required is: 1-Commands attributes: profile ID, cluster ID, end point and pay load to motion sensor 2- Reading mehcanism from the response.

    $13 - $40
    $13 - $40
    0 bids

    My project is to use an arduino circuit like ATMEGA328P Pro Mini 328 Mini and a SIM 800L gprs GSM circuit board, prefered board to be smallest possible or ( if you can recommend better module for this project is fine let me know) conected to a the main alarm control panel and whenever there is an alarm this module call and send a text massage to the

    $3 / hr (Avg Bid)
    $3 / hr Avg Bid
    1 bids

    ...have possibility to change CID number on any SD card. The goal of the project is assemble device or hardware which can change the CID number of any given SD card. It can be Arduino or combination of hardware (PCB) and software - it doesn't matter. The project will be closed when I will see that device or hardware can changes a CID number of a card that

    $184 (Avg Bid)
    $184 Avg Bid
    5 bids

    ...to know how to measure the signal strength of WiFi Access Points and Bluetooth Low Energy advertisers using an ESP32. Do you think you can help me? I would pay for a ESP32 Arduino sketch or FreeRTOS task written in C or C++ or MicroPython or CircuitPython program that you write. The program must constanly scan for Access Points and advertisers, then

    $310 (Avg Bid)
    $310 Avg Bid
    20 bids

    Hello, The goal is to control 4 stepper motors with Arduino Mega + Ramps 1.4 with stepper drivers and with Labview GUI. I have the hardware ready. The task is to write the coding/programming so that it all works as planned.

    $16 / hr (Avg Bid)
    $16 / hr Avg Bid
    28 bids

    Who can code in Arduino to split a string into multiple arrays and after that loop through array and split in N (nummer) and P (character) input string= 100g,40b,100g,1400f,100g,2200c,100g,1400e,100g,400i, output should be array(0)=100g array(1)=40b array(2)=40b etc after that I want to loop through arrays and split that value in n=number in the

    $28 (Avg Bid)
    $28 Avg Bid
    24 bids

    Design a PCB to read an analogue signal from a strain gauge (Load Cell) with the reading ultimately being read using a Raspberry Pi or Arduino. The strain gauge we need to use is an H10J-15t-32-dxx Load cell. Product Details: [login to view URL] Product Datasheet: [login to view URL]

    $1009 (Avg Bid)
    $1009 Avg Bid
    25 bids

    showing details On LCD using Arduino

    $106 (Avg Bid)
    $106 Avg Bid
    76 bids

    We need to...final button push powers down the Gigapan between panoramas to save power, as the whole system will run from car batteries being charged by solar panels. Therefore the Pi or Arduino systems needs to have a little power draw as possible, perhaps even be off between scheduled start-ups at the defined time interval to begin pressing buttons.

    $1024 (Avg Bid)
    $1024 Avg Bid
    16 bids

    hi, i am looking a person who can set my application in arduino base system and develop pcb as require.

    $1229 (Avg Bid)
    $1229 Avg Bid
    1 bids