Finite Element Analysis Jobs

My rocket-shaped quadcopter is already quick, but I want to squeeze out every bit of performance by refining its aerodynamics. Your main mission is aerodynamic optimization, with special emphasis on lowering drag, boosting useful lift, and ensuring rock-solid stability as velocity climbs. The job at a glance • Rework the current CAD model in SolidWorks so centre of gravity and centre of pressure sit exactly where high-speed flight demands. • Run detailed CFD studies in ANSYS or a comparable solver to quantify lift-to-drag improvements, pressure distributions and flow separation—then iterate the geometry until targets are met. • Back the new shape with FEA to make sure the lighter, sleeker frame still meets strength margins and survives prop-induced vibration. ...

I need a complete structural design package for the structural design of only ground floor villa extension including footings, TB, Columns, slab of a 600 SQF (front and rare) single-story residential villa extension that will be reviewed and approved by Dubai Municipality considering the existing structure which might be modified according to the requirement. The site sits on predominantly sandy soil, so the calculations and detailing must clearly demonstrate bearing capacity checks, settlement control, and compliance with the latest Dubai Municipality structural code, as well as relevant UAE load standards. Here is what I expect: • A concise calculation report (PDF + editable spreadsheet) covering gravity and lateral load analysis, soil pressure verification, reinforcement sizing,...

I am looking for a structural engineer with proven experience in CYPE 3D to assist me with the structural analysis of a 2P single-axis solar tracker for a Mechanical Engineering academic project. Proven experience with CYPE 3D is mandatory. Applicants must have actual experience modeling and analyzing steel structures in CYPE 3D. The project is 100% remote, and I would prefer a Spanish-speaking structural engineer based in Latin America. Experience with solar trackers, photovoltaic support structures, light steel structures, wind loads, and Eurocode 3 would be highly valued. The geometry, photovoltaic modules, structural configuration, and main loads are already defined. I also have a similar structural project that can be used as a methodological reference. I mainly need assistance w...

### Hydrodynamic Modelling Validation Freelancer Required I am looking for an experienced **hydrodynamic/coastal modelling freelancer** to assist with **model calibration and validation** for a marine/coastal modelling project. The freelancer should have strong experience in **MIKE 21**, particularly in model calibration, validation, and statistical analysis. ### Scope of Work * Review the existing hydrodynamic model setup and simulation results. * Compare model outputs with **in-situ/current meter observations**. * Perform calibration and validation of: * **Current Speed (CS)** * **Current Direction (CD)** * **Water Level** * Identify the main causes of discrepancies between modelled and observed data. * Adjust/calibrate appropriate model parameters, boundary conditions, bathym...

I am working through Eleation’s HyperWorks course and have 50 pending assignments that must be wrapped up as quickly as possible. Each task follows the standard Eleation template—import the part, create a clean mesh, apply the given boundary conditions, run the required solver (primarily OptiStruct and Radioss), then export results and brief observations. Because this is purely for my personal up-skilling, accuracy and clear step-by-step files matter more than polished presentation. If you have solid, hands-on experience with Altair HyperMesh, HyperView, OptiStruct and Radioss, you should find the workload straightforward; please highlight that experience in your bid. Deliverables • Fully solved model files for all 50 assignments (native .hm, .fem, solver decks) ...

I’m working on an ANSYS Fluent project and I’m facing an error while updating/generating the mesh. The model includes a honeycomb structure, and the Mesh cell is showing an “Error updating cell Mesh” message in Fluent. I need someone experienced with ANSYS Fluent Meshing to fix the mesh issue and make sure the model is ready for Fluent analysis. I can share the ANSYS project/files and screenshots of the error.

I’m working on an ANSYS Fluent project and I’m facing an error while updating/generating the mesh. The model includes a honeycomb structure, and the Mesh cell is showing an “Error updating cell Mesh” message in Fluent. I need someone experienced with ANSYS Fluent Meshing to fix the mesh issue and make sure the model is ready for Fluent analysis. I can share the ANSYS project/files and screenshots of the error.

I have an ultrafast-laser–written waveguide already modelled in RSoft (the .dat structure file is ready), yet every attempt to launch light through it in BeamPROP ends with complete loss of signal. I need an RSoft specialist who can open my file, set up the correct input field and boundary conditions, run the propagation and show where the power is disappearing. Your task will be to: • Configure the launch conditions so the field actually couples into the guide. • Optimise any parameters necessary in geometry or materials to remove the loss of signal (mode mismatch or other distortion could be contributing). • Deliver screenshots, the corrected RSoft project file and a brief note explaining what you changed so I can reproduce the result. When you reply, focus...

I’m ready to commission a complete design-to-production package for a warehouse hydraulic lift dedicated to goods and cargo handling. The unit must safely raise and lower loads in the 1–5 ton range and fit seamlessly into a typical warehouse workflow. What I need from you • Engineering design: Detailed 3-D CAD (SolidWorks or similar), hydraulic circuit diagrams, structural calculations and FEA showing the platform, scissor or ram mechanism, guardrails and locking points. • Manufacturing package: DXF files, machining drawings, welding symbols, full bill of materials with sourced components (cylinders, pump, valves, hoses, power unit). • Compliance & safety: Design must respect common warehouse safety practices and relevant standards (ISO 4413, CE direct...

I’m looking for a structural engineer who already knows the ins-and-outs of steel modular supports used in industrial facilities. The immediate priority is to create new support designs that meet plant load requirements, provide stamped calculations, and fit seamlessly into a modular installation workflow. Once the designs are drafted, I’ll also need you to plan and oversee on-site or lab testing so we can verify load capacity, vibration behaviour, and connection integrity. After testing, I want clear, actionable recommendations—anything from minor tweaks to full redesigns—summarised in a concise report that plant management can act on without wading through pages of theory. Your final package should include: • Signed design drawings (PDF + editable source)...

I have a machine prototype that is already in the detailed-design phase, but I need an experienced mechanical engineer to push it across the finish line. Before anything else, I’d like to review samples of past work that show how you handle similar projects—especially complex mechanisms taken from CAD through to fabrication-ready documentation and validated by simulation. Once I’m confident we’re a good fit, the assignment breaks down into three concrete deliverables: • 3D modeling – refine or rebuild the current CAD so every component fits, moves, and assembles exactly as intended (preferred platforms are SolidWorks or Fusion 360, but I’m open if you use equivalent professional software). • Technical drawings – create fully dimension...